
Installing Weather Guard 5 Gallon Bucket Holder
|
Posted in Install Videos
Saving time on the job starts with smart storage—and installing Weather Guard 5-Gallon Bucket Holder makes it easy to secure supplies without the mess. This simple but effective upgrade is a favorite among tradespeople looking to stay organized and efficient. In this guide, we’ll cover the full installation—from layout and drilling to final bolt-down. You’ll also get a closer look at standout features like heavy-gauge steel construction, an adjustable clamp collar, and a weather-resistant powder coat built for tough conditions.
Why Installing Weather Guard 5 Gallon Bucket Holder Matters
First, loose buckets roll and slam against shelving. Moreover, makeshift holders often fail under load. Therefore, Installing 5 Gallon Bucket Holder provides:
-
Steel-Reinforced Collar: Prevents deformation under weight.
-
Adjustable Strap: Fits standard and specialty five-gallon buckets.
-
Weatherproof Finish: Guards against corrosion and UV fade.
-
Universal Mounting: Works on vans, service bodies, or flatbeds.
Consequently, your tools stay organized. Plus, you maintain a professional appearance on every job.
Tools Needed for Installing Weather Guard 5 Gallon Bucket Holder
Before you begin Installing Weather Guard 5 Gallon Bucket Holder, assemble:
-
7/16″ & 9/16″ wrenches for bolt and nut.
-
Drill + 5/16″ drill bit with stop collar.
-
Socket wrench and extension for quick tightening.
-
Tape measure to pinpoint mounting spot.
-
Marker or chalk to lay out hole centers.
-
Protective gloves to prevent hand injuries.
Meanwhile, unload the cargo area and park on level ground. This prep ensures a smooth, safe install.
Planning Your Mount Location
Next, choose a spot that balances convenience and safety:
-
Ease of Access: Mount near side door for curbside loading.
-
Avoid Obstructions: Stay clear of wiring, drains, and floor ribs.
-
Existing Anchor Points: Leverage D-rings or shelf brackets where possible.
-
Bucket Swing Clearance: Allow full door opening without interference.
Furthermore, a well-planned location speeds up installation and daily use.
Step-by-Step: Installing Weather Guard 5 Gallon Bucket Holder
Now let’s complete Installing Weather Guard Bucket Holder in five clear steps:
-
Mark Drill Points:
- Position holder on van floor or sidewall.
- Use a marker to dot three hole centers.
- Position holder on van floor or sidewall.
-
Drill Holes:
- Fit 5/16″ bit with stop collar.
- Drill through panel, stopping at sheet metal only.
- Fit 5/16″ bit with stop collar.
-
Set Plus-Nuts (if needed):
- Thread each plus-nut onto installation tool.
- Insert into drilled hole and torque until wings flare.
- Remove tool, leaving secure threaded insert.
- Thread each plus-nut onto installation tool.
-
Secure Bracket:
- Place holder over plus-nuts or existing studs.
- Install bolts, lock washers, then flat washers.
- Hand-tighten first, then torque wrenches to spec.
- Place holder over plus-nuts or existing studs.
-
Attach Adjustable Clamp:
- Slide bucket into holder.
- Tighten the adjustable collar until snug.
- Slide bucket into holder.
Moreover, the universal design fits any five-gallon container seamlessly.
Final Inspection After Installing Weather Guard 5 Gallon Bucket Holder
After mounting, perform these checks:
-
Bolt Torque: Confirm each bolt tightens to 15 ft-lb.
-
Holder Stability: Wiggle bracket to verify zero play.
-
Bucket Fit: Test with empty and loaded bucket for smooth removal.
-
Clearance Test: Swing door open to full range without contact.
Finally, you’ll appreciate the rock-solid hold and daily convenience this installer provides.
Maintenance Tips for Your Bucket Holder
To extend service life:
-
Monthly Wipe-Down: Remove grime with mild detergent.
-
Quarterly Bolt Check: Re-torque plus-nut anchors and bolts.
-
Rust Spot Repair: Touch up chips with rust-inhibitor paint.
-
Strap Inspection: Replace adjustable strap if frayed or cracked.
Thus, your bucket holder remains as reliable as the day you installed it.
Ready for Every Job
At Upfit Supply, we recognize that Installing 5 Gallon Bucket Holder transforms van storage into a secure, efficient workspace. With robust steel, easy install, and weatherproof finish, you’ll secure gear and boost productivity in under 30 minutes.
Ready to upgrade your upfit? Shop now:
Watch the full install tutorial: Installing Weather Guard 5 Gallon Bucket Holder
With Upfit Supply, your van works as hard as you do—no exceptions.
Products Used On This Upfit
-
5 Gallon Bucket Holder
Regular price $51.87Regular priceUnit price percheck_box 500+ in stock. Ships in 1-2 business days.
Vendor: