Securing your cargo area isn’t just a smart move—it’s essential. That’s why the Weather Guard Partition for the RAM ProMaster City is one of our most recommended upfits. In this guide, we’ll walk you through every step—from prep to final torque—so you can install a solid barrier between cab and cargo in under 45 minutes. Along the way, we’ll highlight standout features like heavy-gauge steel construction, factory-fit weld nuts, and wide-mesh visibility for added safety and functionality.

Why Installing Weather Guard Partition in RAM ProMaster City Matters

First, loose cargo shifts and creates hazards. Moreover, drilling new holes can void your warranty. Therefore, installing a Weather Guard partition delivers:

  • Factory-Mount Fit: Uses pre-installed weld nuts—no drilling.
  • Durable Steel Construction: Resists dents and corrosion.
  • Wide-Mesh Panel: Maintains rear visibility and airflow.
  • Noise Reduction: Dampens engine and road noise.

Consequently, your van stays organized, safe, and professional.

Tools Needed for Installing Weather Guard Partition in RAM ProMaster City

Before you begin Installing Weather Guard Partition in RAM ProMaster City, gather:

  • Socket wrench with extension
  • SAE sockets: 7/16″ and 1/2″
  • Half-inch wrench and 7/16″ wrench
  • Safety glasses and work gloves
  • Rubber mallet (optional for panel alignment)

Meanwhile, clear out your cargo area and park on level ground. This setup streamlines the install.

Removing Obstructions and Locating Mounts

First, prep the van for partition install:

  1. Remove Cargo: Clear tools and debris from the rear.
  2. Locate Mounting Studs: Identify the six factory studs on bulkhead and side pillars.
  3. Test-Fit Panels: Hold header and base panels in place to confirm stud alignment.

Moreover, leave hardware nearby for quick access.

Step-by-Step: Installing Weather Guard Partition in RAM ProMaster City

Now for the main event. Follow these steps to complete Installing Weather Guard Partition in RAM ProMaster City:

  1. Mount Top Header Panel
    • Hand-thread two ½″ bolts through header into roof studs.
    • Snug bolts until header sits flush, but leave slight play.
  2. Install Side Brackets
    • Align B-pillar brackets over side-wall studs.
    • Insert 7/16″ bolts, washer, and nut.
    • Tighten until bracket won’t slip, yet still allows panel insertion.
  3. Attach Solid Base Panel
    • Lift base panel into position against cargo wall.
    • Hand-thread eight bolts through base into welded studs.
    • Torque with a wrench until panel seats firmly.
  4. Secure Mesh Partition
    • Place mesh panel inside mounted brackets.
    • Hand-thread upper and lower bolts through mesh flanges.
    • Fully tighten all bolts with 7/16″ socket.
  5. Final Torque and Inspection
    • Re-torque header, bracket, base, and mesh fasteners.
    • Check that each panel is centered and plumb.

Meanwhile, the wide-mesh construction and precision-cut steel ensure a seamless fit.

Final Adjustments After Installing Weather Guard Partition in RAM ProMaster City

Once your partition is in place:

  • Verify Visibility: Confirm the mesh offers clear rear sightlines.
  • Test Door Operation: Open and close sliding doors to confirm no panel interference.
  • Inspect Fasteners: Re-check torque on all weld-nut screws.

Finally, load your cargo. The solid barrier and mesh screen combine strength with airflow.

Maintenance Tips for Your Weather Guard Partition

To keep your partition in peak condition:

  • Monthly Wipe-Down: Clean with mild detergent and soft cloth.
  • Quarterly Re-Torque: Ensure all weld-nut bolts remain tight.
  • Touch-Up Paint: Seal scratches to prevent corrosion.
  • Mesh Inspection: Straighten any bent wires to preserve visibility.

Consequently, your van stays secure and looks professional.

Fast, Solid Protection

At Upfit Supply, we recognize that Installing Weather Guard Partition transforms your cargo van. With factory-fit mounting, sturdy steel, and quick install, you get a safe, durable bulkhead in under an hour.

Ready to lock down your ProMaster City? Shop now:
Weather Guard Mesh Bulkhead for ProMaster City

Watch the full tutorial:Installing Weather Guard Partition in RAM ProMaster City

With Upfit Supply, your van works as hard as you do—no exceptions.