A secure cargo barrier is essential for both safety and organization. That’s why the Holman Partition (40670) for the Ford Transit Connect is one of our top recommended upfits. In this guide, we’ll take you through each step—from prep to final installation—so you can get your perforated steel partition in place in under an hour. Along the way, we’ll highlight standout features like heavy-duty steel construction and quick-release mounting that make this upgrade as functional as it is durable.

Why Installing Holman Partition in Ford Transit Connect – 40670 Matters

First, unsecured cargo can shift and damage your load. Moreover, driver safety is at risk without a proper barrier. Therefore, a Holman partition delivers:

  • Sturdy Steel Mesh: Resists impact and contains cargo.
  • Lightweight Frame: Aluminum uprights reduce added weight.
  • Easy Access Door: Hinged section swings open for quick entry.
  • Bolt-In Design: No drilling into van frame.

Consequently, your Transit Connect stays organized and accident-proof.

Tools Needed for Installing Holman Partition in Ford Transit Connect – 40670

Before you begin Installing Holman Partition, gather:

  • Socket set (10 mm–13 mm) for mounting bolts
  • Ratchet wrench and extension for tight spots
  • Trim removal tools for interior panels
  • Measuring tape to align partition
  • Safety gloves to handle sharp edges

Meanwhile, park on level ground and clear your cargo area. This setup ensures a smooth job.

Vehicle Prep

Next, prepare the Transit Connect for partition mounting:

  1. Remove Cargo Tie-Downs: Unbolt existing D-rings.
  2. Fold Front Seats: Push them fully forward.
  3. Take Off Trim Panels: Pry off kick panels with trim tools.
  4. Clean Mounting Areas: Wipe sheet metal to remove dust.

Afterwards, you’re ready to set your partition in place.

Step-by-Step: Installing Holman Partition in Ford Transit Connect – 40670

Now for the core installation. Follow these steps to complete Installing Holman Partition in Ford Transit Connect – 40670:

1. Position Partition Shell

First, stand the partition upright behind the front seats. Align the perforated mesh against the van’s bulkhead. Meanwhile, ensure the cut-out matches cab controls.

2. Secure Floor Brackets

Next, attach the lower brackets to the Transit’s existing floor nuts. Use the provided bolt-in hardware. Then, snug bolts—do not fully tighten yet—to allow slight movement.

3. Attach Upper Crossbar

First, measure between roof mounting studs. Then, hook the crossbar into the studs. Meanwhile, use your ratchet to tighten crossbar bolts. Consequently, the partition shell stays flush against the roof.

4. Bolt in Side Uprights

Next, slide aluminum uprights along the crossbar. Align with floor brackets below. Afterwards, install side-mount bolts through uprights into floor brackets. Finally, tighten all hardware in sequence: top first, then bottom.

5. Install Access Door (if equipped)

First, hinge the door section into place using supplied pins. Then, secure latch catches on both sides. Moreover, test the door swing for smooth operation.

Final Checks and Adjustments

Once hardware is snug, complete these checks:

  • Alignment: Verify partition stands straight, no gaps.
  • Bolt Torque: Ensure all bolts are torqued per instructions.
  • Door Operation: Swing the access door open and closed.
  • Panel Fit: Check that all interior trims refit without interference.

Consequently, your Holman partition works reliably under load.

Benefits and Usage Tips

After Installing Holman Partition in Ford Transit Connect – 40670, enjoy:

  • Enhanced Safety: Protects cabin from shifting cargo.
  • Improved Security: Deters theft by blocking direct access.
  • Professional Look: Perforated steel blends with interior.
  • Easy Cleaning: Wipe or vacuum dust from mesh.

For best performance, occasionally re-tighten mounting bolts and inspect mesh for dents.

A Fast, Professional Upgrade

At Upfit Supply, we know that Installing Holman Partition in Ford Transit Connect – 40670 delivers safety and efficiency in one swift upgrade. With robust steel mesh and tool-free access door, it’s the ideal cargo barrier for any tradesperson.

Ready to upfit your Transit Connect? Shop now:
Holman Perforated Partition for Compact Vans
 Watch the complete tutorial:Installing Holman Partition in Ford Transit Connect – 40670

With Upfit Supply, your van works as hard as you do—no exceptions.

Products Featured In This Video