Assembling the Weather Guard 52

Assembling the Weather Guard 52" x 60" x 13.5" Adjustable Van Shelf

Last updated

|

Posted in Installation Videos

When you're running more than one shelving unit down the side of a van, the small details show. Shelves that line up from one unit to the next look cleaner, load more naturally, and leave room to add doors later without rebuilding anything. In this guide we assemble the Weather Guard 52 inch van shelf with that in mind: wheel well clearance first, accessory spacing second, and every shelf lined up with the unit beside it.

Assembling the Weather Guard 52 Inch Van Shelf

We're building the Weather Guard Adjustable 4-Shelf Unit – 52" W x 60" H x 13.5" D (Model 9375-3-03). It has three 13.5" deep shelves and a 10.5" top shelf, built from fully hemmed heavy-gauge steel with a Brite White ARMOR TUF powder coat. Captive nuts at each corner make assembly simple, and four adjustable dividers per shelf come in the box.

This guide covers assembly only. Installing the shelf in the van is coming in a separate video.

First, scan the QR code on the one-page sheet in the box. It isn't the instructions itself; it links to Weather Guard's latest installation instructions, which are the best advice from the manufacturer.

How every Weather Guard shelf goes together

All Weather Guard shelves assemble the same way. A single bolt goes through the end panel into the shelf at the front, and another at the back. That's it. The real work is deciding where each shelf goes before you start.

Plan your layout

Clear the wheel well

If the unit will sit over a wheel well, the bottom shelf has to clear it. Count holes up from the bottom of the end panel:

  • Ford Transit and Mercedes-Benz Sprinter: location 4
  • Chevy Express, GMC Savana, and Nissan NV: location 5
  • RAM ProMaster: location 6, since its wheel wells stick up much higher

Ours is going in a Ford Transit, so the bottom shelf goes at location 4.

Leave room for accessories

Shelf doors and drawers need specific spacing between shelves:

  • Shelf doors and back panels: 7 hole increments
  • Drawer units: 9 hole increments, counting the hole where the lower shelf mounts

Line up shelves across units

This shelf won't get a door, but it's going next to a unit that will. To keep every shelf in line across both units, we spaced this one to match the door shelf: 7 holes up from the bottom shelf, then 7 more for the next. Plan your spacing across the whole wall, not just one unit, and your shelving will look like one system.

What you'll need

  • The small bag of bolts. That's all assembly takes. The large bag with brackets is for installing the shelf in the van
  • A power drill or driver for final tightening

Step-by-step assembly

Step 1: Seat the top shelf

Start with the narrower top shelf, since the end panels taper at the top. Small lances on the end panel slide into the shelf. They can be snug, so a little stretching or a few light taps up and down will seat it. Add one bolt in the front and one in the back, hand-tight for now.

Step 2: Install the bottom shelf

Doing the bottom shelf next makes the rest of the build easier. Count up to your wheel well location (location 4 for our Transit) and bolt it in.

You can mount the shelves either way:

  • Edges up is how most people go. It cradles your gear, and built-in slots hold the dividers.
  • Edges down gives you a flush top, handy for a Packout mount.

Step 3: Add the middle shelves

Bolt in the two middle shelves at your planned spacing. For us, that's 7 holes above the bottom shelf, then 7 above that, matching the unit next door.

Step 4: Add the second end panel

Start the second end panel slightly low so you can get the top shelf into its lances, then work it up into place. Line up each shelf with the same holes you used on the first panel.

Step 5: Check and tighten

Double-check every shelf position so nothing ends up cockeyed. Then go through with a power tool and tighten every bolt.

Before it goes in the van

Add accessories first, if you can. Back panels, doors, and drawers are often easier to install outside the van. Just plan for the weight: the shelf alone is about 90 pounds, so you might need help getting a loaded unit in.

Choose your install method. Use the included brackets and set plus nuts in the van's wall structure and floor, or use a Weather Guard mounting kit for your make, model, and wheelbase. The kit's channel system mounts to the van, and the shelf mounts to the channels.

Shop the Weather Guard Adjustable 4-Shelf Unit – 52" W x 60" H x 13.5" D

Planning a lockable shelf? The Weather Guard Shelf Door for 52" Shelf Units fits this width. Browse all van shelving for other sizes and accessories.

FAQ

What hole should the bottom shelf go in?
Location 4 for the Ford Transit and Mercedes-Benz Sprinter, 5 for the Chevy Express, GMC Savana, and Nissan NV, and 6 for the RAM ProMaster.

How do I space shelves for a door or drawers?
Leave 7 hole increments for a shelf door or back panel, and 9 for drawer units, counting the hole where the lower shelf mounts.

How do I line up shelves across two units?
Use the same hole locations on both units. If one unit has a door at 7 holes, space the matching shelf on the other unit at 7 too, even if it won't get a door.

Which hardware bag do I need for assembly?
Just the small bag of bolts. The larger bag with brackets is for installing the shelf in the van.

How heavy is the shelf?
About 90 pounds before accessories.

We want you empowered to make your own upfitting decision. If you'd rather talk it through, our US-based upfit pros are ready to help.

Products Used On This Upfit